![]() That’s all about controlling the fan speed. Therefore, after choosing the SYS Fan 4 in the dropdown, I can see the RPM as shown below: The SYS Fan shows nothing here because by default it shows the RPM of SYS Fan 1 and I have installed my fan on SYS Fan 4. Click on the cog icon to adjust the speed of the respective fan.Īdjust the graph as per your needs and then move on to the next fan. You can see the RPM of CPU Fan, PUMP Fan, but nothing in SYS Fan. The same is shown on the next screen below: In my case, I have nine fans in total and have used CPU Fan1, PUMP Fan1, and SYS Fan 4 on my motherboard. Note the pins on the motherboard where you attached your fan pins to. Finally, click the cog icon under Customize as shown below: Open up the Dragon Center app and click on User Scenario. Having said that, before using any software, you should make sure that the fan mode is set to PWM in the BIOS otherwise the speed that you adjust in the graph won’t have any affect. So, if their software works for your motherboard then I would suggest using it if you don’t like the software from your own brand. I have to mix linux and mswin support, since I want the same app for both. Generally speaking, the software by MSI are the best I’ve have used so far. I need a fan control app for my msi gf75. ![]() As I have a MSI motherboard, it made sense to me to use the software by MSI. If you prefer a simpler way to change the fan speed then doing so via a software would be the way to go. You should notice the fan speed change instantly or after saving the configurations. After doing the changes, you can save the new configuration and start using the pc. You have to choose PWM mode if you really want the speed to go down (like 10% of the max speed or so). You should bear in mind that you can’t reduce the voltage below a certain threshold and therefore, you can’t really slow down the speed to a minimum such that you hear no noise. If you choose DC mode then you can only adjust the supply voltage. Once you enter the BIOS, you can look for Fans, select PWM mode, and then finally adjust the speed-to-temperature graph ensuring that the Smart Fan Mode is turned on. Press F2 or Delete key when your PC is botting up (the keys maybe different depending on your motherboard).Press and hold Shift key and then click Restart.You can open the BIOS Dashboard in either of the two ways: In my case, the Antec Prism fans are PWM fans so I can precisely control what speed I want them to run at. The PWM fans allow for a seamless and high-precision control whereas the DC fans lack precision as their speed is controlled by varying the supplied voltage. The PWM fans are 4-pin fans whereas DC fans are 3-pins. PWM fans are DC fans but with an extra wire for PWM. With the help of a software (Dragon Center for MSI Motherboard).īefore we dive into how to control the fan speed, we should be aware of the two modes the fan operates in – PWM and DC.There are two ways you can control the fan speed (RPM) in your PC: Having said that, the process should be similar for other fans and motherboards. Open RGB can control the GPU but not the motherboard (they had bricking issues so they disabled motherboard control for the time being).In this blog post, we are going to see how to control the fan speed/RPM of Antec Prism ARGB 120mm fans on a MSI X570 Tomahawk Motherboard. RGB might be a sticking point if you're worried about that. That way you can forgo Dragon Center entirely. Plug the fans into that and use iCue to control it all - or pick up a Commander Pro and do the same. IF you are really worried about system temps, I see you have a Corsair AIO. The Monitoring section of Dragon Center has been pretty good - sometimes it reads the CPU temp (especially on the 5800X (I have one also)) wrong/higher than it should be - but that seems to be an issue on other things too, CAM and even AMD Ryzen Master gives funky numbers (AMD have said they are fixing this This month). Your experience may be different, I have 6x Noctua NF-12x25 fans in my system lol. I've had no issues with the Frozr AI thing, just set it to performance leave it be. There is Two ways to control fans in dragon center, the "Frozr AI" set and forget kinda thing, or using the custom "Scenario" thing and change fan profiles n stuff that way. I don't have too many issues with it, sometimes it spams WMI with errors causing higher than usual cpu usage, but can fix that just by restarting the service, doesn't happen too often, it's mostly a Mystic Light-caused thing. Dragon Center is kind of a personal preference or love/hate kinda thing.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |